Search Results

Manufacturers of carbureters and ignition devices are called upon to assist in overcoming troubles caused by the inclusion of too many heavy fractions in automobile fuels. So far as completely satisfactory running is concerned, the difficulty of the problem with straight petroleum distillates is caused by the heaviest fraction present in appreciable quantity. The problems are involved in the starting, carburetion, distribution and combustion. An engine is really started only when all its parts have the same temperatures as exist in normal running, and when it accelerates in a normal manner. Two available methods, (a) installing a two-fuel carbureter, using a very volatile fuel to start and warm-up the engine, and (b) heating the engine before cranking by a burner designed to use the heavier fuel, are described and discussed.

ENGINEERS have different ideas regarding highly efficient and moderately efficient engines, but designers dare not ignore the fact that the public requires today a small very high-speed engine, with good torque at low speeds, and capable of revolving efficiently at very high speeds. These two characteristics are difficult to attain, since in practice one is really opposed to the other. To obtain high speeds with power, the valve areas, valve parts, carbureter, etc., should not be restricted in any way, while to get a good mixture at low speed with heavy torque means a different valve-setting and more or less restricted port and valve areas, etc., to secure high gas velocities. The author states that the fundamentals of high-speed engines are high volumetric efficiency; high compression, to aid in obtaining rapid combustion at high speeds, and light reciprocating and rotating parts, to secure high mechanical efficiency.

THE impression that recent aircraft experience should have taught engineers how to revolutionize automobile construction and performance, is not warranted by the facts involved. Aircraft and automobiles both embody powerplants, transmission mechanisms, running gear, bodies and controls, but their functions are entirely different. The controls of an airplane, except in work on the ground, act upon a gas, whereas with an automobile the resistant medium is a relatively solid surface. Similarly, the prime function of the fuselage is strength, weight considerations resulting in paying scant attention to comfort and convenience, which are the first requirements of an automobile body. Aircraft running-gear is designed for landing on special fields, and is not in use the major portion of the time. The running-gear is the backbone of an automobile, in use continuously for support, propulsion and steering; hence its utterly different design.

The author states as his object a review of what has been done and what must be done to make tractors successful in operating on low-grade fuels, especially kerosene. He takes up in order the four principal methods in common use of applying heat to vaporize kerosene, pointing out the advantages and disadvantages of each method and of its modifications. The author then cites various experiments with different types of carbureters in burning kerosene, drawing at length upon his own experience in this connection. He cites difficulties with gas distribution, manifold condensation, pistons and spark-plugs and points out that carbureter design is inseparable from considerations of tractor engine and manifold design. That better progress has not been made in the past in developing kerosene-burning tractor engines is stated to be largely owing to the fact that there has not been sufficient cooperation between engine and carbureter manufacturers.

The authors outline some of the problems that confront the automobile engineer today, showing how the demand for better performance and economy and the ever-increasing cost of volatile fuels has emphasized the necessity for thorough engineering work in the successful automobile manufacturing plant. Believing that the accurate analysis of the heat distribution in a modern automobile engine will be of great value, the authors describe a comprehensive test, made under their direction, of such an engine. This test includes measurements of the brake horsepower, friction horsepower, fuel consumption and heat losses to jackets, exhaust and cooling air. The engine tested was inclosed in a hood, similar to that used on the car in normal service and an air blast was directed through this hood at speeds approximating those at which the engine would drive a car with a given gear ratio.

This paper discusses the principles of battery ignition and then describes high-tension magneto ignition. A comparison between the two types of ignition is given, and the paper concludes by illustrating diagrammatically how and why a very hot spark causes the engine to produce more power and to economize on fuel consumption.

The author first compares mineral oils with certain other liquids in order to point out clearly certain of their characteristics. He then shows the economic benefits that would result from making more of the crude available for use as fuels. He discusses such topics as cracking methods in use, advantages of dry gas, initial flame propagation, gas producers, hot mixtures, wet mixtures and difficulties of correcting existing engines. He concludes by proposing as a solution of the gasoline problem the more general use of superheated homogeneous fixed dry gases made in vaporizing devices independent of engine cylinders, and outlines means for attaining this end. Performance data covering the use of mixtures of kerosene and gasoline on several cars are included in a table, and several charts throughout the paper illustrate many of the topics discussed.

The author states that the objects of the paper are to define and trace the development of the various processes of carburetion, and to offer such suggestions along these lines as may assist the investigator in developing motorboats, automobiles and self-contained unit motor cars for railway purposes. The surface carburetor is mentioned chiefly as of historic interest. In considering the jet carbureter the author discusses the proportion of gas desired, the effect of the varying inertia of the air and the liquid gasoline and the breaking up of the combustible needed. Following sections review the devices for using kerosene, such as gasoline jet carbureters to which heat is applied, devices of the fixed gas type, the introduction of combustible directly into the cylinder, forcing combustible directly upon a hot surface in the cylinder and devices which raise the combustible to the boiling point.

Many areas of the world are in various stages of development which frequently includes a rapid increase in the motor vehicle population. As a result, some areas are beginning to show the effect of increased motor vehicle use on air pollution. The vehicle's contribution to California's air pollution has long been recognized and studied, and measures have been implemented to reduce emissions from motor vehicles. The history of light duty vehicle emission control in the South Coast Air Basin of California is reviewed. Emission reductions achieved, current levels, projected future emissions and the need for further emissions reductions from light duty vehicles are discussed. For other areas of the world where motor vehicles contribute to air pollution, suggestions are made which can improve the effectiveness of emission control efforts; which should be consistent with political and economic realities, and efforts to achieve international harmonization of standards.

A survey of the in-service fuel consumption of passenger vehicles and derivatives in the Australian fleet was carried out in 1984-85. Seven hundred and four owners across Australia took part in the survey. Vehicle owners reported by questionnaire the amount of fuel used during four tank fills of normal operation, the distance travelled, and other details of the operating circumstances. The survey shows a clear downward trend in the fuel consumption of the Australian passenger fleet. The data also provides comparisons of actual fuel consumption obtained on the road, with laboratory derived values for fuel consumption. Vehicles in a sub-set of 40 were fitted with fuel flow meters during the survey and tested to Australian Standard 2077 for fuel consumption. The questionnaire method is shown to be a valid and accurate technique for determining in-service fuel consumption.

To improve the cold startability of methanol, methanol-butane mixed fuel was experimented. Engine performance and exhaust emissions are obtained with methanol-butane mixed fuel. These characteristics are compared with those of methanol and gasoline. The mixing ratios of methanol and butane are 50:50 (M50), 80:20 (M80), and 90:10 (M90) based on the calorific value. As a result, M90 produces more power than gasoline and more or less than methanol depending on the engine speed and the excess air ratio. Brake horse power of M90 is higher than that of gasoline by 5 - 10 %, and brake specific fuel consumption is smaller than that of gasoline by 17 % to the maximum based on the calorific value. NOx emission concentrations for M90 are lower than those for gasoline and higher than those for methanol because of the effect of butane, CO emission concentrations are somewhat lower than those for methanol and gasoline.

In order to achieve lean burn engine control system, it is necessary to develop high accuracy air fuel ratio control technology including transient driving condition and lean burn limit expansion technology. This paper describes the following. 1 The characteristics of the transient response of the fuel supply are clarified when various kinds of air flow measuring methods and fuel injection methods are used. 2 To achieve stable combustion in lean mixture, fine fuel droplet mixture, whose diameter is less than 40 μm, needs to be supplied.

A procedure has been developed for evaluating equivalent drive cycle emission results from raw exhaust gas emissions data obtained from an engine under test on a computer controlled Vehicle Simulator Engine Dynamometer. The emitted species data is integrated with the air intake flow rate to determine the total mass of emissions, after correcting for the reduction in exhaust gas mass due to precipitation of the moisture of combustion. This procedure eliminates the need for the Constant Volume Sample (CVS) System attached to the vehicle exhaust while undergoing simulated drive testing on a chassis dynamometer to evaluate compliance of the test vehicle with the Australian Design Rules, ADR27 and ADR37. Sources of error with the procedure are examined by comparing the fuel consumption measured using a volumetric technique during the test with that evaluated by a carbon balance procedure as given in the Australian Design Rules.

The sequential fuel injection, in which fuel is injected into swirl being generated for mixture stratification, was used to pursue the potential of a lean burn engine for its performance improvement. As a result, it has been found that the most effective method to increase thermal efficiency while reducing NOx emission level is to combine a high-compression compact combustion chamber located on exhaust valve side in cylinder head with DICS (Dual induction Control System). This method was used to build a high-compression lean burn concept vehicle, which was evaluated for compliance to various emission standards. Testing showed that the concept vehicle can improve fuel economy by 10.5% on the Japanese 10-mode cycle, by 8.3% on the ECE mode cycle, and by 6.3% on the U.S. EPA test mode cycle while meeting respective emission standards.